Banner U-Gage Ultrasonic Sensor Manual do Utilizador descarregar pdf (Página 11)

SENSORS

More information online at bannerengineering.com302

LIGHT GAUGING ULTRASONIC MEASURING ARRAYS RADAR

Class 2 (Visible Alignment Laser)

Lasers that emit visible radiation in the wavelength

range from 400 to 700 nm where eye protection is

normally afforded by aversion responses, including the

blink reex. This reaction may be expected to provide

adequate protection under reasonably foreseeable

conditions of operation, including the use of optical

instruments for intrabeam viewing. Reference 60825-1

Amend. 2 © IEC:2001(E), section 8.2.

Class 1 (Infrared Sensing Laser)

Lasers that are safe under reasonably foreseeable

conditions of operation, including the use of optical

instruments for intrabeam viewing. Reference

60825-1 Amend. 2 © IEC:2001(E), section 8.2.

Operating Mode

Laser Class 1

Setup Mode

Laser Class 2

Do not stare into beam

L-GAGE

LT7 Speciﬁcations

Minimum Analog

Window Size

LT7PLVQ: Not Applicable

LT7PIDQ: 300 mm

Adjustments

Push-button-directed password enable/disable, measurement unit select, offset value select, output limits set, output mode select,

analog output slope select (diffuse models only) and output limit manual adjust. See data sheet for information.

Serial Interface

RS-422 or SSI compatible

Serial Measurement Speed

SSI: 1.4 milliseconds (SSI cycle 80 microseconds) RS-422: 2.9 milliseconds

57.6 kBaud

Indicators

4 LEDs:

Green: Power ON/OFF

Red: Alarm (Error) LED

Orange: Output 1 and Output 2 conducting LEDs

2-line digital LCD display. See data sheet for detailed information.

Construction

ABS shock-resistant housing; PMMA window; polycarbonate displays

Weight

Approximately 230 g

Environmental Rating

IEC IP67

Connections

12-pin M16 connector; 100 m max. cable length; use only cables listed on page 302.

Operating Conditions

Temperature: -10° to +50° C in continuous operation

Storage Temperature

-30° to +75° C

Vibration/Shock

EN 60947-5-2

Application Notes

• All specifications are based on the specified surface at constant ambient conditions and following a minimum operating time of 15 minutes.

• For best accuracy, allow a 15-minute warmup before programming or operating

• Crosstalk avoidance: Light spots must be separated by at least 200 mm.

Certiﬁcations

Hookup Diagrams

MI05 (p. 759)

(cont’d)

Brackets

LT7

SMBLT7

pg. 658

M16 QD

See page 697

Length

Threaded 12-Pin

Straight Right-Angle

3 m MQDC-1210ST MQDC-1210RA

10 m MQDC-1230ST MQDC-1230RA

30 m — MQDC-1290RA

Cordsets

REFLECTORS

PAGE 710

REFLECTORS

Additional cordset information available.

See page 679.

Additional brackets and information available.

See page 620.

Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 65 66

Comentários a estes Manuais

Sem comentários

Banner U-Gage Ultrasonic Sensor Manual do Utilizador Página 11

Comentários a estes Manuais

Manuais e produtos relacionados com Medição, teste e controlo Banner U-Gage Ultrasonic Sensor