Banner A-GAGE MINI-ARRAY Series Manual do Utilizador descarregar pdf (Página 14)

14 P/N 43298 rev. E

Banner Engineering Corp. •Minneapolis,MNU.S.A.

www.bannerengineering.com•Tel:763.544.3164

MINI-ARRAY

InstructionManual

Installation and Mechanical Alignment

Figure 3-2. MINI-ARRAY emitter and receiver mounting bracket dimensions

Mounttheemitterandreceiverintheirmountingbrackets(showninFigure3-1),

andpositiontheredlensesofthetwounitsdirectlyfacingeachother.Theconnector

endsofbothsensorsmustpointinthesamedirection.Measurefromoneormore

referenceplanes(i.e.,thefloor)tothesamepointsontheemitterandreceiverto

verifytheirmechanicalalignment.Ifthesensorsarepositionedexactlyverticalor

exactlyhorizontal,acarpenter’slevelmaybeusefulforcheckingalignment.Extending

astraight-edgeorastringbetweenthesensorsmayhelpwithpositioning.Alsocheck

byeyeforline-of-sightalignment.Makeanynecessaryfinalmechanicaladjustments,

andhand-tightenthebrackethardware.SeeSection5forinformationonalignment

indicatorsandtheuseofthealignmentsoftwaresuppliedwiththecontroller.

Connecttheshieldedcablestotheemitterandreceiver,androutethemtothe

controllerlocation.Followthelocalwiringcodeforlow-voltagedccontrolcables.The

samecabletypeisusedforbothemitterandreceiver(twocablesrequiredpersystem).

Cutthecablestolengthaftermakingsuretheyareroutedproperly.Removecablebraid

atthecontrollerconnectionpoints(seeFigure3-4).

3.2 Controller Mounting

ThecontrollermustbeinstalledinsideanenclosurewithaNEMA(orIEC)rating

suitablefortheoperatingenvironment.

MountingdimensionsforthecontrollerareshowninFigure2-2.Thecontrolleris

suppliedwithM3.5x0.6hardwarefordirectmountingtoasurface,oritcanbe

mountedontostandard35mmDINrail.

3.3 Emitter and Receiver Hookups

Emitterandreceivercablesconnectinparalleltocontrollerterminals#4through#8.

Connectthewiresfrombothsensorcables,asfollows:

  Terminal4 Brown

  Terminal5 Blue

  Terminal6 Bare

  Terminal7 Black

  Terminal8 White

Trimoffthefoilshieldandthebraidedshieldatthepointwherethewiresexitthecable

(seeFigure3-4).

The“drainwire”istheuninsulatedstranded

wirewhichrunsbetweenthebraidedshield

andthefoilshield.Removethefoilshield

andbraidedshieldatthepointwherethe

wiresexitthecable.

Figure 3-4. Emitter/receiver cable

preparation

Tr im braided shield flush

with cable

Tr im foil shield flush

with cable

Uninsulated

drain wire

Emitter or

Receiver

8.1 mm

(0.32") max.

0.5" (13 mm) radius minimum bend

71 mm

2.8"

Figure 3-3. Quick-disconnect cable

clearances

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 43 44

Comentários a estes Manuais

Sem comentários

Banner A-GAGE MINI-ARRAY Series Manual do Utilizador Página 14

Comentários a estes Manuais

Manuais e produtos relacionados com Sensores Banner A-GAGE MINI-ARRAY Series