Banner PresencePLUS Interface Modules Manual do Utilizador descarregar pdf

SCM

†

Strobe Control Module

Printed in USA

05/01 P/N 67448

Features

• Strobe control module for Banner strobed LED lights

•Two independently-adjustable strobe light output circuits designed to strobe LED

lights up to 60 Hz

• Direct plug-in connection to Banner strobed LED lights via the 9-pin

D-sub connector available on models of strobed lights

• Removable (plug-in) terminal block for power and trigger signal connections

• Separate trigger inputs for each output channel; inputs accept 5 to 12V dc trigger

signal

• Simple switch selection of either high to low or low to high trigger signal

• One 3 m (10') shielded cable for trigger signal is supplied

• Output pulse width adjustable using binary DIP switches from 5 to 1,315 microseconds

(separate adjustment for each output channel)

• Black anodized aluminum housing

Specifications for Model SCM

†

Strobe Control Module

WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or

replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty

period. This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any

other warranty either expressed or implied.

Environmental Rating IEC IP20; NEMA 1

Operating Conditions Temperature: 0° to 40°C (+32° to 104° F)

Maximum relative humidity: 95% at 40°C (non-condensing)

Input Power 24V dc ±5% at 2.0A max.

Power supply model PSC-24(E) is recommended (see Accessories)

Fuse: 5 x 20 mm fast-acting 3A, externally accessible

†

This model is not stocked and is non-returnable.

Outputs Two independently-adjustable 24V dc ±5% outputs, 9A peak max.

Strobe rate: 60 Hz max.

Pulse duration: Adjustable from 5 to 1,315 microseconds in 10 microsecond increments

Note: Outputs use 9-pin D-sub connectors which allow direct plug-in connection of Banner strobed LED lights

Trigger Inputs Two inputs - one for each output channel

Each input accepts 5 to 12V dc signal, 10 mA max.

Switch selectable for high to low or low to high trigger signal

Note: Use two-wire shielded cable for trigger signal(s); one 3 m (10') trigger cable is provided with SCM module

1 2 3 4

Resumo do Conteúdo

Página 1 - Strobe Control Module

SCM†Strobe Control ModulePrinted in USA05/01 P/N 67448Features• Strobe control module for Banner strobed LED lights•Two independently-adjustable stro

Página 2 - SCM Strobe Control Module

SCM Strobe Control Modulepage 2Banner Engineering Corp. • Minneapolis, U.S.A.Website: http://www.baneng.com • Tel: 763.544.3164Light 19-pin D-sub co

Página 3

page 3SCM Strobe Control ModuleBanner Engineering Corp. • Minneapolis, U.S.A.Website: http://www.baneng.com • Tel: 763.544.3164Outputs Light 1 and L

Página 4

Banner Engineering Corp., 9714 Tenth Ave. No., Mpls., MN 55441 • Ph: 763.544.3164 • www.bannerengineering.com • Email: [email protected]

Mais documentos para Transmissão Banner PresencePLUS Interface Modules

Para ver o documento Banner PresencePLUS Interface Modules Manual do Utilizador

Banner PresencePLUS Interface Modules Manual do Utilizador (1 páginas)

Comentários a estes Manuais

Sem comentários

Banner PresencePLUS Interface Modules Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Transmissão Banner PresencePLUS Interface Modules. Banner PresencePLUS Interface Modules User Manual Manual do Utilizador

Resumo do Conteúdo

Mais documentos para Transmissão Banner PresencePLUS Interface Modules

Comentários a estes Manuais

Manuais e produtos relacionados com Transmissão Banner PresencePLUS Interface Modules